... the bearings are pressed on to the shafts. Thanks John. Apparently that bearing had become seized to the shaft. I did finally get it off.. the bearing is...
George, Goo job1 I know it's a messy job but take some pictures if you think about it. It may help the next guy that has to do it. John in Seattle ... From:...
Thanks Joe Let me tell you what I am up to. My X-9 is a wonderful machine but the rear shocks are poor. They are also a weird European size and about 14.25...
... I've already tried some penetrating oil on the screw...I'll bring out the torch next. I haven't yet removed the front wheel. I thought I would reseat the...
Hello with my power upgrades I have managed to blow the final drive on my '86 CH 250! One of the small pin roller bearing blew and went straight into the cogs...
UPDATE: So Friday afternoon I finally had a few hours to devote to checking into the source of my fuel leak. I removed my seat and my panels and had a good...
... <saabman.aero@...> wrote: I have been reading with intrest your methods of removing ... If you have an AutoZone auto parts store anywhere near you you can...
Does anyone have a tank for this girl? I'd hate to see her stranded due to failed putty. John in Seattle ... From: laura_scigliano <laura_scigliano@...> ...
I had the same problem with my speedo screw. tried so hard to get it out the screw eventually snapped in half. then I pulled on the cable too hard and broke...
I have a good tank for $10 + shipping. Jack From: CH250HondaElite@yahoogroups.com [mailto:CH250HondaElite@yahoogroups.com] On Behalf Of John D Sent: Tuesday,...
another one bites the dust. i doubt if you've really provided that much extra HP to the transmission that it blew. what were squeezing out, an extra 5mph...
The VHD's have 5 different settings to adjust the softness or stiffness of the ride. I paid $69.61 including shipping. If you want to pay that I'll get them to...
Well it seems that the contershaft bearing is the one that died :-( the tranny is basically a mess boohoo not sure what to do... Maybe buy a replacement...
Greetings, I just wanted to take a minute to introduce myself to the group. I just purchased this new to me scooter from a private party over the Labor Day...
saabman wrote: Comment: Well it seems that the conter shaft bearing is the one that died, the tranny is basically a mess boohoo not sure what to do. Maybe buy...
Hey everyone has been a yr. since the last post maybe more. I lost the keys to my 1990 CH250 and need to fix. What do you suggest as the best way to remedy...
As far as I know there is a code stamped on the side of the ignition switch. You will have to remove some plastic body pieces to get to it, and you might have...
Yup happened to me.... That frickin Countershaft bearing! I believe InTransit told me to inspect it to see if the case was hammered. It was...... I also tried...
Jack, You're a saint! I'll buy the gas tank from you. Please e-mail me with how you would like your payment (I do have paypal) and how much for shipping to...
Paypal is fine Laura. Please contact me through my scooter web site (www.jacksscootershop.com) with your zip code and I'll figure out the shipping cost. This...
Welcome! I was a 1986 Honda Elite 250 newbie a few months ago. I love my scooter and am learning a lot about it through this forum. The people on here are...
First, order a replacement OEM screw. They don't cost all that much. When you've gotten it, remove the old one with a screw remover bit before you remove the...
Sorry to take so long in writing back. A lot going on. I did get the cover off and it appears that the problem was just terminal corrosion. I pulled the cover,...
I took my 1985 Ch250 into the local Honda shop for a rearvalve stem replacement and new brake shoes. When I got it back later that day I noticed that the...
It depends on where you are reading. Enough. Let's talk scoots. John in Seattle ... From: in transit <fpgaman_2000@...> Subject: Re: [CH250HondaElite]...
I have a small leak in the bowl of my carb and I am not sure which is the best route to take to fix it. In Feb of this year I overhauled the carb which...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
