Hopefully that thread is stopped dead in it's tracks... I've been reading with envy all you guys who live in warmer climes (and some of you brave souls that...
Mike, I'm just finishing up final drive bearings. I priced them out through the stealership and through a local bearing house in Kent WA. The price was a...
I have a 1990 CH 250 that's missing the upper and lower front covers, and the garnish. Would these parts from 1985 through 1989 models fit my 1990 scooter?...
only 1989. DROSS4646 <dross4646@...> wrote: I have a 1990 CH 250 that's missing the upper and lower front covers, and the garnish. Would these parts from...
OK I'm on the cusp of finishing my final drive. Just waiting for a gasket for that. So while I'm at it, I decided to get new clutch shoes. Al I need to do now...
... From: Mike To: CH250HondaElite@yahoogroups.com Sent: Wednesday, November 01, 2006 1:13 AM Subject: [CH250HondaElite] Re: Tiananmen Square Hopefully that...
... From: John D To: CH250HondaElite@yahoogroups.com Sent: Wednesday, November 01, 2006 6:28 AM Subject: Re: [CH250HondaElite] Re: T Square threaded to...
Mercuriallists I have a Chinese belt sander in my garage. I have had it and used it for years and it still works fine. Got a good deal on it too. Not to sure I...
bahsarie wrote: Question: Does anyone know if the carb on the helix and 250 are the same for an 86? Answer: Close. The CH250 is a 28mm bore and the Helix a...
John, Thanks for the tip regarding bearing house prices versus the stealership. I'll check into that. I'm a synthetic oil guy all the way. The Honda takes so...
MIke, I couldn't get my wife on the back of the scooter for anything. I did buy a BMW K-bike a few months ago and after several agonizing pleads, I was able...
The place I bought my bearings from in Kent WA is Applied Industrial Technologies. Over the weekend I'll dig out the receipts and post the part numbers of...
Hi Mike There are two types of passengers. Back warmers and helmet knockers. Helmet knockers don't normally start back pounding until they are getting monkey...
Mike There is an election coming up perhaps you would prefer to ask if we think that George Bush and the right wing republicans are going to destroy the...
Does anyone know where I can get a front axle, axle nut and spacer for my '85 Elite 250? Bikebandit.com does not show these parts on any of their schematics....
what are "Demarcates"? Mark Piper <b1b4uc1@...> wrote: Mike There is an election coming up perhaps you would prefer to ask if we think that George Bush...
John, Wait! Don't spend all that money! Get a new seal for the gas cap under the seat! If your dealer can't get one, make one. I spent Xhundreds of dollars...
If you are really bored, once you get the part number, you can go to Cycle-parts.com and get it for a little less. Hinshaw's listed the axle for $11.69....
Hello all - Due to a blustry windstorm here this afternoon, my parked 86' CH250 fell over on its right side. There doesn't seem to be any cosmetic damage...
Hi David It is probably fine. Check the fluids like you said . I have had cracks develope after a fall over so take a real close look at the plastic. Brake...
was it on the center stand ??? i had one fall over on side stand [Non-text portions of this message have been removed]...
shutda2@...
Nov 4, 2006 1:50 pm
7312
Unfortunately I only have a side stand. The center stand was torn off (including the mounting holes) before I purchased the scooter. It had a rain cover on it...
Can someone tell me how the starter motor is supposed to be wired up on an '85 CH250? One runs from teminal (or that nut on the side) on starter motor to the...
Can someone tell me how the starter motor is supposed to be wired up on an '85 CH250? One runs from teminal (or that nut on the side) on starter motor to the...
I HAVE an actual "motorcycle". Makes no difference to her. She won't ride on that either. I hadn't thought about this before, but come to think of it, she's...
Wait, do NOT try to start it up! Only dissapointment and danger lie down that road. Instead, immediately sell your scooter to me for $200. Send me your address...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
