Hi, I'd like a bit of information regarding circuit bending my newly acquired 'casio sk-200'. I basically just need to know which chips to stay away from, so I...
Generally, any point on the board that has a power supply voltage on it, such as 7.5V DC, or 5V DC. You can safely check these points before trying them if you...
Hello. I was wondering. Disscussion is about SK samplers so You must have some of Your music made on these machines. I would be very pleased to hear it. I'm...
yerzmyey@...
May 14, 2008 7:28 am
367
Yerz; That is a good point. Maybe there is or could be set up in the forum list a section for music files. I often go searching for songs on the sk's myself....
If you check out the track Sullen Lamplighters on my Myspace page you'll hear a bunch of bent gear, including an SK-1. The SK-1 makes the higher pitched...
My band (Systems Theory) have just released a free album on the net which you can get to at http://www.mikedickson.org.uk/codetalkers If you have a listen to...
Can anyone put me in touch with someone who can repair my "casio sk-200" sampling keyboard? It stopped working today... It powers on, and the keys play the...
I don't have an SK-1 to tell you by looking at it's board and showing you, but I can tell you where to find them using the SK-1 service manual. On p28 of the...
Ahh, OK, I see what you're trying to do. You want to do a pitch LFO, right? If that's the case, the SK CV outs are not what you want. The SK CV's are for...
New to mods and would like to do a cv sync with my first experimentation on the SK 5. Can someone point me twards a step by step guide I looked in the files...
OH sure i see thanks again! would i be able to combine two of the LFO circuits and connect them to the same point using the vactrol in order to have 2 VCO's?...
Yes, you can combine them. What were you planning to do with the 2nd VCO, some sort of ring modultion as well? Cheers, graham ... LFO circuits and ... VCO's?...
You could try checking out this thread here: http://launch.groups.yahoo.com/group/CasioSK/message/219 It was regarding doing that with the SK-1 though. Still...
i was planning to connect both of them to the pitch so i could combine waveforms, e.g square wave on one and triangle on the other. would they still work...
Yes, they will. Actually, you'll get some unique sounds out of it if the LFO rates are set at different rates to each other. Cheers, Graham ... combine...
Hi. I'm bending my sk-1. I've gathered all I could find about it and experimented on that: Pitch (just pot and body contact), poly, skew, found the drums...
... that link anymore. So what I remember is I should solder the direct out to the negative leg of a 4.7uf capacitor, then pass through a 3k3 resistor and out...
Sounds like you've been pretty industrious! "would like to have your opinion on them, just out, after the envelope/pitch circuits (adsr?)" Yes, and depending...
Well I did those 4 outs but the volume is really low, drums volume very low, melody I can barely hear, bass and chord I can't even hear. Is that normal? I...
Ok, then try tapping each voice after each of its amplifying section, before they're combined together. On each of the voice lines, this would be just before...
Oh, and for the drums, I'm not sure. There doesn't seem to be an amplifier circuit for it. Try tapping it at points along the drums line, starting directly out...
Yep, I got to the multimeter test probe pretty fast. I found some interesting things: C38,42,46,50 are the spots to tap the 4 voices out. The volume is good ...
hi, i have this circuit almost built. i want to connect it up to the voice and audio 1 out. should i do the 'vactrol' method in connecting it? i haven't...
Yes, just connect the vactrol's photoresistor to the SK circuit board points, then just attach it to the LFO's LED. But check to see that it works first. After...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
