TUESDAY 2ND OF DECEMBER THERE WILL BE A OPEN NIGHT AT THE VANCOUVER HACKER SOCIETY.THIS NIGHT WILL BE CONCENTRATING ON CIRCUIT BENDING AND OTHER TYPES OF...
tuesday 2nd december there will be an open night at the vhs ,vancouver hacker society. The night will be devoted to circuit bending ,arduino programming and ...
I need a little help - my SK-5 seems to have stopped sampling. I've checked all the usual stuff, ie removed ALL of the bends, cleaned and checked all the pins...
It sounds like there is a problem with the trigger input for the sampling section. Whenever you sample, and the sampling section does not receive a signal over...
If I perform this mod, will the sk be sending signal out of the speaker and the new output jack at the same time? Also, would the volume slider then only work...
Hey Jordan! In my SK8, the direct out does not affect the speaker out - you get both, which is really cool. The speaker volume control will only work for the...
The CDP200: http://www.casio.co.uk/products/Musical%20Instruments/Digital% 20Pianos/CDP200RST/At_a_Glance/ Although its sampling memory isn't very good by...
Hi Robert, The URL doesn't work because stupid Yahoo refuses to render the entire link as a web address once they get past a certain length. Just copy and...
Hi there, after a few busy months I'm back to the Sk. I couldn't get the other method mentioned working (most probably my error) but did get several ocatves of...
Hi all, so I bent my casio sk-1 and I know how to build an LFO using a 555 timer ic. I found two points on the sk-1 pcb that when shorted trigger the...
you could use the 555 to trigger a small reed or ss relay. Find a simple LED blink circuit, and put the relay in line with the led. Or find an led relay...
i dont really know if a transistor would work- but they our kinda out of my area of knowledge... not to good with them yet. But i generally look at them as...
Solid state relays are kinda expensive. I don't know much about transistors either, but I have been reading up in wiki, and it says they're used as amplifiers,...
you could also try going CMOS the 4066 is 4 switches in one. When there is a high voltage (or maybe it's a low ) at the control pin, it will allow the...
Hey everyone, I have an SK-5 that I have spent a ridiclous amount of time housing in a nice wooden case and bending. It worked fine until the other day. I...
Ok, now something very strange is happening. I was fiddling around by the chip where the main bends are, and I foud a couple of points, that if I connected...
Hi Robodelfy, I was gonna reply to your first post and ask if it ran ok on batteries but you've already gone there. As the resident electronics engineer and...
Hey, thanks for the reply... I did it all so carefully and all the joints look good, but I might try and re do some of them. Isnt it a bit strange that it...
Robodelfy, The SK1 I got at a garage sale didn't have the wall wart, so I bought one of those voltage-selectable ones at Radio Shuck. Not to get your hopes up,...
hi! a small EP can be found here >>> http://www.jamendo.com/en/album/16954 first take, improv session... instruments we used: casio sk-1 yamaha vss casio pt-82...
... instruments we used: casio sk-1 yamaha vss casio pt-82 cheap distortion pedal all of the instruments are circuit bent enjoy! ;-) ... Many thanx for this...
yerzmyey@...
Apr 7, 2009 11:03 am
507
hi! i´ve broken the original crystal in my sk-1 when i installed an additional pitchbend oscillator. does anybody know the frequency for the standard pitch? ...
Hello, I'd like to bypass the anti aliasing filter on my SK-5, but the files section only describes the mod for SK-1. Is it the same? If it's not, where do I...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
