Hi there, after a few busy months I'm back to the Sk. I couldn't get the other method mentioned working (most probably my error) but did get several ocatves of...
Hi all, so I bent my casio sk-1 and I know how to build an LFO using a 555 timer ic. I found two points on the sk-1 pcb that when shorted trigger the...
you could use the 555 to trigger a small reed or ss relay. Find a simple LED blink circuit, and put the relay in line with the led. Or find an led relay...
i dont really know if a transistor would work- but they our kinda out of my area of knowledge... not to good with them yet. But i generally look at them as...
Solid state relays are kinda expensive. I don't know much about transistors either, but I have been reading up in wiki, and it says they're used as amplifiers,...
you could also try going CMOS the 4066 is 4 switches in one. When there is a high voltage (or maybe it's a low ) at the control pin, it will allow the...
Hey everyone, I have an SK-5 that I have spent a ridiclous amount of time housing in a nice wooden case and bending. It worked fine until the other day. I...
Ok, now something very strange is happening. I was fiddling around by the chip where the main bends are, and I foud a couple of points, that if I connected...
Hi Robodelfy, I was gonna reply to your first post and ask if it ran ok on batteries but you've already gone there. As the resident electronics engineer and...
Hey, thanks for the reply... I did it all so carefully and all the joints look good, but I might try and re do some of them. Isnt it a bit strange that it...
Robodelfy, The SK1 I got at a garage sale didn't have the wall wart, so I bought one of those voltage-selectable ones at Radio Shuck. Not to get your hopes up,...
hi! a small EP can be found here >>> http://www.jamendo.com/en/album/16954 first take, improv session... instruments we used: casio sk-1 yamaha vss casio pt-82...
... instruments we used: casio sk-1 yamaha vss casio pt-82 cheap distortion pedal all of the instruments are circuit bent enjoy! ;-) ... Many thanx for this...
yerzmyey@...
Apr 7, 2009 11:03 am
507
hi! i´ve broken the original crystal in my sk-1 when i installed an additional pitchbend oscillator. does anybody know the frequency for the standard pitch? ...
Hello, I'd like to bypass the anti aliasing filter on my SK-5, but the files section only describes the mod for SK-1. Is it the same? If it's not, where do I...
Hello, I'm trying to build the "Simple VCF" like the tutorial in the filessection. First I used a AD822 opAmp; had one leftover with only one side working...
Which version of the circuit board did you make? The upper, generic one, or the lower, specially adapted one for the Casio SK? If you're using the bottom one,...
HI! This is a sample loop created with the internal sequencer http://www.youtube.com/watch?v=X_mebQKmpU8 This technic of looping is simple. step by step : 1)...
hello all! first post.... im about to go pick up a lovely sk100 wondering if anyone had any experience with this lil beast? im very curious.... as i havent...
Hi, first I like to thank you for your answer, I already read it a week ago or so, just were too busy to write back. I didnt actually find out where my mistake...
Glad you got something up and running! When you want something later with CV input you can always try building it again - but just start with the simple layout...
... Hello, you can find a link to the sk-100 manual on www.casiosk1.com. I have the sk-200 which is functionally identical to the sk-100, but mine is stereo....
Just got my first SK Cracked it open for the first time... As I was putting it back together I think I screwed the keypad circuit board in to tight. A few of...
Just look carefully at the board and make a stocktake of any broken tracks in the circuit board you can see. Then get a soldering iron and simply bridge each...
Not as such on the SK-1 but it will work exactly the same. The SK-1 will have the same type of CV envelope lines as the SK-8, obviously on a different part of...
Thanks for replying I would solder them all back but they are too close together. The solder would drip onto more than one circuit at once. there's about 10 of...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
