June 1st. Good Wed.! Bry from Indiana (so. part) here. Just bought a used (traded in) DTX III. So far (a couple of days) i've had a little trouble with it,...
Bry, Welcome. A factory reset probably wouldn't be a bad idea to start with. I would expect all the attenuation switches to be down on a standard setup. If you...
... Bry, I'll expand a little on Keith's points. After your factory reset, switch into Live Mode, as opposed to Practice Mode, if you aren't there already...
Bry, Headphone choice is probably the most critical to the volume and sound quality. I have 2 different sets of Sony studio headphones that work great. I don't...
To add to Keith's thoughts, check the volume switch on each individual trigger pad. You will need a little screwdriver for this. Clockwise turns it up, and...
What's up everyone, I just recently purchased a new dtxpress III special and I'm using the sony mdr-7506 headphones and it sounds killer! but I'm looking for a...
This was asked in the DTX forums.. What should I use to clean my pads with? K...I'm going to address this question with my scientific opinion. Please feel free...
... the ... systems? ... Hi Tony, At the prices that most of us can afford, it would be hard to beat the coherence and control of good phones like the Sony...
I have found the Behringer KX1200 amplifier to be pretty good. However, you don't get the stereo sound. I was thinking of getting a high-watt PC speaker system...
... However, you don't get the stereo sound. I was thinking of getting a high-watt PC speaker system like the Logitech z-2300 as an alternative or supplement. ...
I have assembled the "cheap DTXpander" circuit that Keith posted to this site recently and have had partial success with it. A mono trigger wired to input J3...
Keith, Do you think the Z-2300 would work in a very small auditorium that seats about 50 - 75 people ? ... However, you don't get the stereo sound. I was...
i am close to 50 now. so i have been playing for a number of years...lol too many. i already have the p a speaker setup, but found getting the correct mix was...
... The DTX 2.0 will not adjust your way out of this problem. Have you got an output adjustment on the pad itself? If so, increase the pad signal as much as...
... seats about 50 - 75 people ? ... I am afraid I have no idea what is required for performances - only practice. I can ask my drum teacher on Wednesday when...
Jerald, After spending a week or so looking for a monitor system for my kit (DTXpress III SE) and reading what people had to say on this site I decided to jack...
... The z-5500d system is ... sound ... a chance, ... try the ... how it ... I'd suggest ... powered ... an ... I have no intention to rain on this parade. I...
Yes, parts are available from yamaha drums. For slippage, add a piece of felt or rubber skid pad to the clamp betw the bar. Another possiblilty: look for the...
... I will post a second opinion from my drum teacher on Wednesday. I trust his opinion because he makes a living drumming, has a TD8 and, I think, 400W 15"...
Hi all, just an introduction: I'm a new DTXpressI owner - picked one up for a bargain just yesterday! I'd been reading this forum for a few weeks while I was ...
... Welcome. There is an adjustment on the front of the hi-hat pedal so you don't have to press it down so hard. There are photos of most of the components in...
Hi There As a recent purchaser of a second hand DTXpress III I have had great fun over the last couple of weeks re-introducing myself to the joys of playing ...
... great fun ... playing ... Denon ... various ... the ... listen back ... Hi Mark, Congratulations on picking up the kit and welcome to the group. I assume...
Keith, PFozz, plhalli, et al: First off, I'm a regular poster on DIYedrums, but maybe I should pay more attention to the DTX groups :) Keith, fabulous work!...
... out the diode on the main pad (D2, essentially removing it from the circuit) which cured the sensitivity problem on the main pad. I might have had the...
... It was getting late last night and I forgot about the real reason for D2 - to stop one pad loading the other. Without it, the signal from the pad with D1...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
