again i've broken my a121 vcf 2 multimode filter by connecting the +-12v the wrong way. last time i had it repaired and they putted a new cem 3320 inside. so...
Hello Floris, basically I think it's possible that you've fried more than one chip. However, the CEM3320 is not easily to come by. Synthtech (home of MOTM)...
What is the A-117 CV response like? Is it vaguely exponential? linear? Is this a Shift register based noise circuit where the CLOCK is under VC? I am looking...
Has anybody ever tried processing audio with the 166? What were the results? Tony _________________________________________________________________ In a rush?...
Hello, I wasn't actually going to post here, as I thought it bad form, but with both Dieter and Bakis stating that information on other manufacturers is...
Hi, Here is the last list of modules and others stuffs I sell: - 1 x Doepfer A-122 24db LP VCF - 1 x 55 Euros - 1 x Doepfer A-131 exp VCA - 1 x 45 Euros - 1 x...
For Sale Doepfer A-154 Enhanced Sequential Controller, A-155 A-155 Analog/ Trigger Sequencer both purchased from Analoguehaven in last couple of months (the...
Hi Tony, ... linear? ... under VC? Yes, the A-117 produces a simple shift register sequence, but no, it is not under voltage control. Thus there is no 'CV...
To clarify 1 x A-154 and 1 x A-155 (not two) I have received several emails asking price reduced to USD $515 plus shipping ... [Non-text portions of this...
Thanx Tim, I should have looked more closely! Pretty obvious there is no CV but rather an ext. clock input. Any idea how long is this sequence? Can you notice...
Hey gang, A gig note: I'm playing a couple of shows this week with German tubaist Carl Ludwig Hübsch, whose playing sounds electronic a lot of the time. I'll...
all the best with the Gigs, Gino! sadly i am quite far... ... Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist [Doepfer_a100] group owner www....
Hi Tony, ... using high frequency clocks? Personally, no I can't, at least it is not obvious to me in the way that some sequences I've heard are. At high clock...
Just before I dive in, does anyone have advice or experience of drilling through doepfer module faceplates? I want to put an extra switch across jumper J1 of...
If I were adding a switch to a doepfer module I would remove all electronics and center punch the BACK of the panel before I drilled. I would run my machine at...
i mean this really unfacetiously: i find it inspiring that there are people out there who are so capable and diligent. i just want to get a hole through with...
How about this, instead of going at the 112 panel, just buy a blank 4hp panel and put the mod into that, install the panel next to the 112. If you are feeling...
I did made holes in the A199 reverb to put RCA out and also add switch for CV1 on A110... and I'm not such of a DIY guy... I just used a dremel like machine,...
... In any case the clock of the A-149-1 QRV section affects the A-149-2. I'm not sure if the QRV knob setting and CV affects the A-149-2 too. This depends if...
... <<snip>> ... Well, I just couldn't let it rest at that! I'm now pretty sure the sequence is at least 2^19 = 524288 long, so at 1kHz (approx knob setting...
... The A-117 has no CV input ! ... No, you only have a clock input and can use e.g. a VCO or HSVCO (e.g. from one of the BBD modules) as VC clock source. Best...
... In any case the clock of the A-149-1 QRV section affects the A-149-2. I'm not sure if the QRV knob setting and CV affects the A-149-2 too. This depends if...
Yes, Yes, I apologize for such a silly question. I should have looked more closely at the panel! Or better yet the manual. Tim's analysis of the sequence is...
How about this, instead of going at the 112 panel, just buy a blank 4hp pane and put the mod into that, install the panel next to the 112. If you are feeling...
... I've got the answer from Christian. The CV of the A-149-1 QRV section does not affect the A-149-2 outputs as the "raw" shift register data are taken for...
Hello - I have a need for a circuit to convert triggers to gates. I have found the Doepfer Trigger Delay created to wide a pulse. Wondering if others need this...
A142 and A162 would do it. I'll try a clock divider as well cause I don't have those modules (first trigger : gate open / second trigger : gate close). Best, ...
... Actually it's not possible to convert a trigger into a gate signal in the usual meaning as the trigger is a short pulse only but has no time length. If you...
Dieter - We spoke before on this issue. I may have improperly set the A162 but as I remember even at the shortest of delay lengths it produced too wide a...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
