... It depends upon the built in power supply ! The old version A-100TN12 had only 650mA (manufactured until about 2001), the new version A-100PSU2 has 1200...
24419
isoldeandisobelle
isoldeandiso...
Jan 23, 2013 12:33 pm
Yes, it is the PSU2 version. Thanks again....very helpful....
24420
christian ienni
ienni23
Jan 23, 2013 9:08 pm
hmmm.... maybe i should do some homework! i've always just gotten the modules i wanted and installed them where they fit, and have never even looked at power...
24421
achtung_999
Jan 23, 2013 10:58 pm
I seem to have been running way too much in one of my old 6U cases for more than a year I noticed... I have to hand to the maker of http://www.modulargrid.net,...
24422
christian ienni
ienni23
Jan 24, 2013 6:28 am
out of curiosity, what is the symptomology you have noticed, i.e. what specifically happens that leads you to think there's a current issue? so i can maybe...
24423
achtung_999
Jan 24, 2013 10:30 am
Well to be honest I never noticed a thing. Until I started, for fun, to build my rig on http://www.modulargrid.net and noticed that I was way over 650mA with...
24424
achtung_999
Jan 24, 2013 10:33 am
For the record: I just reordered all modules so I'm within limits again... On Thu, Jan 24, 2013 at 11:30 AM, achtung_999 < ... [Non-text portions of this...
24425
christian ienni
ienni23
Jan 24, 2013 8:43 pm
ah, i understand. since all of my cases are the newer 1200mA PSU2 versions, i doubt i'm pushing any limits, since as i said i've never noticed any problems, or...
24426
achtung_999
Jan 25, 2013 1:04 am
The worst thing that might happen will be fuses blowing regularly. That is a sign. ... [Non-text portions of this message have been removed]...
24427
metronomezine
Jan 25, 2013 11:21 pm
So have 2 A-196 PLLs that i've been fooling around with -Raul's World of Synths latest video on the A196 pushed me to play with them today. I never bothered to...
24428
christian ienni
ienni23
Jan 26, 2013 12:17 pm
belated happy new year to everyone! :-) new track for the new year - "entropy engine 1" some shamelessly indulgent berlin-school sequenstravagasm wankery...
24429
Raul
raulpena1974
Jan 28, 2013 2:22 am
Just a minor question on the PLL. In the manual it states that PC2 is linked to the LED. However there is a fair amount of activity occurring when using the...
24430
ddoepfer
Jan 28, 2013 10:14 am
... The data sheet of the PLL circuit (74HC4046) mentions the function of this pin (PCPout) only if phase comparatur PC2 is used (the PCPout is part of the PC2...
24431
ddoepfer
Jan 28, 2013 12:11 pm
... There are three different versions of the A-196 module available. The main difference was between version 1 and version 2 (manufactured from about end of...
24432
Raul
raulpena1974
Jan 28, 2013 12:17 pm
Thanks for that clarity. I'll keep that in mind. I'll include that addendum to the video information for the next few. All the best. Raul Pena...
24433
Robert Crouch
rcrouch
Feb 1, 2013 6:02 pm
Turns out it's not the glide option after all. I think I need to send it in for repair....
24434
James Husted
ersatzplanet
Feb 2, 2013 7:41 am
I recently got an A-152 and am using it to select the columns of two of my PGM-4X4 programmers to make sequences that can have programmable patterns to them....
24435
Jesse Buehler
pwjpb
Feb 2, 2013 12:42 pm
James, Synthetic Sound Lab's V-Gates will do this. In its Analog mode, cv input can be swept in different ways to its 8 outputs as triggers. It also produces a...
24436
James Husted
ersatzplanet
Feb 2, 2013 8:58 pm
The V-Gate function mentioned as "A clock output is available that produces a 1 millisecond (ms) pulse for each change of output state." is exactly what I am...
24437
Jesse Buehler
pwjpb
Feb 2, 2013 10:42 pm
Perhaps, but keep in mind it also covers the a-161, a-149-1 and the gate aspects of the a-152. For all of that, $250 is not that bad. Sent from my iPhone ... ...
24438
ddoepfer
Feb 4, 2013 8:54 am
Did you (re-)install a jumper to the pin header JP4 on the interface/supply board instead of the glide option ? Best wishes Dieter Doepfer...
24439
ddoepfer
Feb 4, 2013 9:26 am
... This is also available as an internal "hidden" feature since about 2005. The RC4 port pin of the microcontroller (pin 6) outputs a short pulse whenever...
24440
James Husted
ersatzplanet
Feb 4, 2013 6:21 pm
Thank You Dieter! I was sure that something like this was available. I will probably make something like this to attach to it: Nice that it is on an expansion...
24441
James Husted
ersatzplanet
Feb 4, 2013 6:26 pm
Forgot - no attachments in this forum! basically The thing I attached was a transistor circuit (2N5088) and some resistors and a LED to drive the output jack....
24442
Robert Crouch
rcrouch
Feb 4, 2013 7:13 pm
Yes I did. The problem is fairly consistent where it received midi fine until it's been plugged in for a while, then it just stops. I have to unplug it for...
24443
ddoepfer
Feb 5, 2013 8:38 am
... Yes, please return the unit for repair and add a short description of the fault. Maybe it's a thermal problem. Thank you Dieter Doepfer...
24444
ddoepfer
Feb 5, 2013 9:04 am
... One row of the expansion connetor is connected to GND. The five pins of the other row are connected to the port pins RC0...RC4 of the PIC processor. So far...
24445
charles kerr
thebadproducer
Feb 6, 2013 12:03 pm
Hi James, I'd be interested to see your expansion circuit if possible, sounds like a cool addition to the 152! Would it be possible to email it to me or drop...
24446
sweetsynthchuck
Feb 7, 2013 5:17 am
Hi guys, First post here, I am very much intent on getting a combination of the units above for processing duties, my question is there any overlap between the...
24447
Florian Anwander
fanwander
Feb 7, 2013 8:36 am
Hello and welcome! ... Let me describe it soundwise: The A116 can sound similar to a simple fuzz box, but has many setting, which can make the sound "thin". I...
