No, but i do have some modules (and some other rare and interesting trinkets ... See my page at: http://www.numberofthebeast.org/forsale2.html Some of these...
Hi Tomek ... A CV-input might be quite difficult, but ist should be easy to add an clock input which should be fed by a highspeed VCO. The highspeed VCO could...
hello michael, nice to have you on board :-) do you like the erwik filter? it caught my attention a few years ago, but i refused to buy it because of the high...
Thanks! The erwik filter is quite good, I like setting "2" the most. It's quite good, even though I haven't used it that much yet. I bought it for about 3-4...
Hi Ingo, i have the Erwik filter too. I think it sounds really beatiful, I use it a lot. But at a slightly lower price the A-107 can do the same and more,...
hello daniel, the a107 uses a cem 3379. just a short question, does the erwik start oscillating at full resonance in all filter modes? i'm especially ...
just checked, resonance selfoscillates at these filter modes: 1. no (1 pole Low) 2. yes (2 pole Low) 3. no (3 pole Low) 4. yes (4 pole Low) 5. no (1 pole High)...
Out of curiosity, is this filter still available, and if so where from? Thanks David David Salter Senior Project Manager Reuters Ltd Tel +44 20 7542 2402...
I'm not sure if they just haven't updated the site in a long time but they seem to have one left here: http://www.analogue.org/network/frames24.htm (it's the...
Florian, thanks for the answer, could you mail me with more info on that (priv or group). i'm not sure how to implement a clock into the signal chain. thanks...
hello daniel, many thanks for that info. looks a lot like the a107. best wishes ingo ... I ... months ... regular ... your ... move ... construction, ... info ...
right, thats where i've seen it too. i asked for the price of that module quite a while ago, before the a107 was released. they wanted nearly 500 euros for it,...
Hi Tomek ... The clock is NOT in the signal chain. This clock is a rectangle signal within the circuitry of the Flanger-stompbox. You have to find it on the ...
500 euros is too much for me. I like mixing modules from other makers but as I already have a 107 I'll pass. Thanks for the info David Salter Senior Project...
Hi, I bought my filter second hand for about 10-15 euros, not sure how much, it was a part of the bargain with the cabinet and the other modules. I actually...
hello david, same with me, the price was simply too high. i don't know if the price is still valid, but i don't see why the price should be much lower now. ...
hello michael, phew, 10-15 euros is damn cheap, you're lucky :-) yes, afaik the erwik filter is a limited edition, only 12 were made. best wishes ingo ... how ...
Hello all, I'm in the company today as we have to take inventory during we are closed and found some messages from the group. Here are my comments to some of...
Dieter Doepfer
hardware@...
Jan 4, 2006 11:12 am
9516
... additional CV ... CV1 ... control the ... hello dieter, that is a great addition, a very good idea. best wishes ingo...
So I'm scaling back a bit and selling a Doefper A-100G3, that's a 3 space rack with a power supply. Excellent condition, it had only one module in it and never...
I bought a doepfer module recently and I was wondering if I could install that into a AS1600 case from analogue solutions. I heard that the doepfer modules...
Hi Dan, Glad to see you found the group. Theres no consolidated manual, but if you find the module overview page, and look at the individual modules, all with...
hello, you just have to make sure that the red stripe of the power cable is connected to the -12 volt pin of the buss board. in doepfer cases the red stripe is...
hello all, the following example shows the sonic differences of filtered and unfiltered clock noise in a bbd module. this example is taken from the a188/1...
hello, and finally the cd has been released and is available from cdbaby: http://cdbaby.com/cd/chrysalid this double cd has been made to help the victims of ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
