Dear members, many customers from USA, Canada and other countries ask how they can find out the acting type (fast/medium/slow) of a fuse. As you may know the...
9757
Dieter Doepfer
hardware@...
Feb 6, 2006 10:01 am
You have to set the clock dividing factor to 6, 12 or 24 to get 1/16, 1/8 or 1/4 hardware clock pulses from the A-190. Please look at the A-190 manual to page...
9758
Dieter Doepfer
hardware@...
Feb 6, 2006 10:08 am
TD, yes. As the current @+5V is taken from the +12V rail you have to add the +5V current. For the A-113 the total current is 150mA provided that the low-cost ...
9759
Dieter Doepfer
hardware@...
Feb 6, 2006 10:19 am
TD, replacing the power supply should not be necessary. In any case you have to pay attention that the correct fuse (250mA for the standard PSU, 500mA for ...
9760
Florian Anwander
florian_anwa...
Feb 6, 2006 1:08 pm
Hi ... since ever. This is what lists like this one should be configured. If you have a binary file, please place it to the files section. ...
9761
Zoran Bosnjak
synth_addict
Feb 6, 2006 2:18 pm
Hello, I have three G6 racks. One is fine. The second one has been dying on me for months now. The fuse stays INTACT, hard tap at the back in the area of power...
9762
Zoran Bosnjak
synth_addict
Feb 6, 2006 2:38 pm
Hello, here are the markings embedded into metal parts of the 0.5 A fuse I use for 1.2 A power supply: One one end: 500mA 250V On the other end: FSL (+ some...
9763
Florian Anwander
florian_anwa...
Feb 6, 2006 2:41 pm
Hi Zoran ... Thank god! I thought it would never end ;-))) ... If the correct fuse is used: a misbehaving module cannot blow the PSU permanently. The power...
9764
Dieter Doepfer
hardware@...
Feb 6, 2006 6:01 pm
At the weekend I began to finish the development of the BBD module (additional CV out, polarizer for CV2 ...) I found that we overlooked a very important...
9765
Adam-V
spiralsect
Feb 6, 2006 10:15 pm
Hi folks, Apologies in advance for the long post but I couldn't think any other way to introduce myself! I'm new to the group and have just made a start on my...
9766
Tommy DOG
revmutt
Feb 6, 2006 10:53 pm
Here is the Radioshack fuse information I am using with my 6 space rack with older power supply, Part number 270-1063, 1 Amp Slow-Blow Fuses, 250 volts, 5 X...
9767
Zoran Bosnjak
synth_addict
Feb 6, 2006 11:07 pm
According to the reply from Mr. Doepfer, you are using wrong fuse. If your power supply is 0.650 A (the old one), you should not use fuse with higher value...
9768
Tommy DOG
revmutt
Feb 6, 2006 11:27 pm
First, thank you to Dieter and everyone, I'm sorry for the length of this post but I am hoping the details will help. The issue first appeared after I switched...
9769
Tommy DOG
revmutt
Feb 7, 2006 2:23 am
... Thanks Zoran, Apparently I am continuing to aid my own troubles. Of course Radioshack looked at the original fuse and handed me these. Now if only I could...
9770
adam-v@...
spiralsect
Feb 7, 2006 3:39 am
... your ... higher ... trouble. ... TD I'm not sure what size the fuse package is (I haven't looked yet) but assuming it is the standard 1 1/4" x 1/4", the...
9771
Sixtoo.1200Hobos
sixtoogotdrums
Feb 7, 2006 5:15 am
Hello Dieter and also to the rest of the folks on here. Thanks for the feedback. I checked page 10 in the manual, and since I am not sending midi messages via...
9772
Dieter Doepfer
hardware@...
Feb 7, 2006 9:51 am
Sixtoo, the clock divider module A-160 will not really help as it divides only by 2, 4, 8 ... I know that the A-190 programming is a bit awkward but it should...
9773
Dieter Doepfer
hardware@...
Feb 7, 2006 9:51 am
Thank's Adam-V, according to this document time lage fuses are marked by a "T" (same as in Europe). Best wishes Dieter Doepfer...
9774
Tommy DOG
revmutt
Feb 7, 2006 4:16 pm
Is the older power supply always regular PSU? TD...
9775
Tommy DOG
revmutt
Feb 7, 2006 5:39 pm
... Okay, so we have two values here: 400MA & 500MA Voltage listed at 250. To make it clear, in my case I am using a old power supply which can handle up to...
9776
Bakis Sirros
synth_freak_...
Feb 7, 2006 6:07 pm
hello, in my case, when the a155 sequences seem to me a bit "off-sync";, i use the a160 divider plus the a162 dual trigger delay. with the right a190 clock...
9777
tkrakowiak
tomekrakowiak
Feb 7, 2006 6:26 pm
hello, my fuse struggle ended with one of those: ...
9778
Adam-V
spiralsect
Feb 7, 2006 11:49 pm
Sorry to add to the confusion! I thought you were after the catalogue numbers for the 500mA Slow Blow Fuse. I think this is the information you are after...
Can anyone tell me if these pedals will work in the Foot Ctl. 2 input of the A-177 foot controller module, just to get high/low voltage for gate/trigger? (I...
9781
Dieter Doepfer
hardware@...
Feb 8, 2006 10:06 am
The required type of pedals and double footswitch is mentioned on page 4 of the A-177 manual. If the devices match to these specs they will work. Foot Ctrl....
9782
Dieter Doepfer
hardware@...
Feb 8, 2006 10:07 am
Yes. The first PSU2 were delivered fall 2004 (only as an option, not all A-100 frames delivered since fall 2004). From 2006 all frames include the PSU2 (except...
9783
ErnstKarel
lerake
Feb 8, 2006 11:57 am
Thanks very much for the reply. What I'm wondering, though, is if a standard keyboard sustain pedal/switch, if plugged into the Foot Ctrl 2 input, will give...
9784
ErnstKarel
lerake
Feb 8, 2006 12:46 pm
In case anyone is interested, I just posted two photos in the 'Photos' section (under the title of "suitcase mods") of a couple of crude modifications I've...
9785
Florian Anwander
florian_anwa...
Feb 8, 2006 3:02 pm
Hi Ernst, ... No. But I think, there is aworkaround for you: The Foot Ctrl2 is intended for the usage with a potentiometer (see fig 1 on page 4 of ...
