i have 5 SSM2056 if you want i can sell it for 40 dlls including S&H to your country .. i'm from mexico city... or if you have other parts for synth maybe we...
How many of them for the 40$ ? ... S&H to your country .. i'm from mexico city... or if you have other parts for synth maybe we can trade.. i don't accept the...
just one gil_we <gil_we@...> wrote:How many of them for the 40$ ? ... S&H to your country .. i'm from mexico city... or if you have other parts for synth...
Hi everyone, I just recently found this group and I think its great. I have had my Polysix for about six months and have had nothing but problems, such as...
excuse me, this is probably asked all the time.. I just checked the ricard/johannes hausensteiner thing. (it sounds really cool, but some links broken - it...
I have an old P6 that I'm restoring. I've manged to get every part working but the damn thing will not tune. I substituted the voice board and CPU board over...
I have an old P6 that I'm restoring. I've manged to get every part working but the damn thing will not tune. I substituted the voice board and CPU board over...
... If the battery leaked then it is likely that IC30 & IC31 on KLM367 will need replacing. You may have some tracks that have corroded too that will need...
The side panels are part of the lower wooden case and are not available seperately. You will have to do some woodwork or get a chippy to sort this for you ;---...
Hi all again, Just to let you know that it was in fact the opto on the oscillator board. I have several of these boards with the same problem and this has been...
Hello PS6ers. Just got one of these babys which looks great with my Sigma. I bought this thing knowing it didn't work hoping it was a battery problem but I...
... that my power supply -15v and -5v were shot. I'm still trying to figure out why but check those voltage via the test point on the power supply board to see...
I back again. I was able to track and find the problems with the power supply. Replaced the Regulator and transistor and my outputs are good and stable....
... Has the battery leaked? Have you already fixed it? Without the battery and with all parts around the battery ok, the Polysix functions 100%, it only can't...
Hi, I am trying to reset the factory sounds on my polysix. I have downloaded the data (.wav of the original tape) from http://analog.no/ and have followed...
using these old machines liked you to tweak the "tone control" on your little cassette recorder - turning it towards the treble - computer soundcards tend not...
... The battery leak on my Polysix was very hard to see, but it damaged the memory circuit board and the nearest chip underneath so that I had complete sound...
... It's possible - have someone with knowledge of electronics open the thing up and check that the "tape in" wires are connected at both ends and the socket...
... that if the traces to the processor or IC31 are damaged you possibly will not get any sound? Does this also hold true if you try to play it in "manual...
Correct -- even in Manual mode, it won't work. The Polysix (& other "memory" synths) runs ALL of its control voltages thru the CPU -- any problem on the data...
... narrow diagnosing time for me. Looks like I'll better get my soldering iron and a wire out. ... voltages thru ... reflected in ... trace ... tracing ... in...
... So is this what makes the Polysix have DCO's? Today I checked the resonance voltage at CN05-7 and found out it's rastered, because I couldn't set it to...
... Eh, not exactly... ... OK, I was giving a simplified answer. To be more exact, on a memory type synth, all CVs are multiplexed & turned into digital...
Ok..... Rebuilt the power supply. It now works, Changed the battery and re traced most of the area. replaced the 74LS08 next to the battery but still now...
Check the Crystal Quartz and also check the lines with a scope from the CPU ... regards, lnz2166 <lnz2166@...> wrote: Ok..... Rebuilt the power supply....
Thanks to all who gave suggestions on my recently purchased Polysix blue light special. Here is what I've done so far: 1. Power Supply was blown. Changed the...
Hi, I don't know. But have you already tried to clean them ? You should use pure alcohol for the copper/gold contacts. If there are still markings on the gold...
Hi, Thanks for the reply. I have already had them cleaned but the technician said a couple of them are on there way out. I assume this would be a common...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
