Hi - Thanks for adding all those - look forward to checking them out... (Just been looking at the pictures of your MIDI board - pretty clever stuff. Done any...
Anyone have a polysix that is just extremely dull - looking? I am wondering what would be the safest cleaner/wax to use on the painted finish of the control...
i decided i'll etch the board myself. now - is there anyone that could get me an already programmed PIC? or maybe point me to a good (tested) schematic for a...
I've got two Polysixes now. I've had one for a year, bought it, replaced the battery. Also bought a Kenton Midi Kit for it but never had it installed, got it...
first check the level switch (low/hi/off) to the left, the volume knob near it and the attenuator knob (-10 to +10) left of arpreggiator. obviously the process...
... Well if you don't have an oscilloscope available you are limited to guessing which part or board might be defective. ... If I were in your shoes, I'd do...
I hope this doesn't sound stupid, but did you try doing the tape/.wav dump again to make sure that it was loaded in correctly? I know there's that issue with...
Greetings all, Just picked up a filthy, beatup but mostly workin' polysix. Keyboard contact needs cleaning etc. Fortunately the battery isn't leaking but it's...
Hello everybody, I recently got my SSM 2044 chips and installed them into my Trident MK2. I managed to tune the VCF resonance using VRx01 - 03 on board...
i don't know about the trident but on polysix you have 2 pots for filter tuning (you're actutally tuning cutoff, not resonance): one for VCF offset one for VCF...
... Yes, true, as the SSM2044 will produce a sine wave at its cutoff frequency. ... I can't match those names with any hearing expierence from my tuning. ;-) ...
well on polysix there are 3 trimpots on the top of each voice chain. i think the first is cutoff CV offset and the second is scale. i'm not 100%. i could be...
I am having a terrible time tuning my PolySix. I can get all 6 banks in tune with each other no problem. I cannot get C0, C3, and C6 in tune at the same time....
Hi, I've recently acquired a Korg Polysix (mk 2 with no KLM-396 board), which was in pretty bad shape. I've changed the battery, which luckily had barely...
A friend of mine has the exact same problem on his board, we haven't managed to find the source of the problem yet though. ... luckily ... be ... been ... ...
... Try to get only the first oscillator in tune first. GENTLY take all SSM's out except of the first oscillator,a and press the Unison key. Now you can hear...
I managed to cobble together a working Polysix from 2 dead units and a rebuilt 367 from Old Crow. The oscillators sound pretty in tune, so I left them alone. ...
... This means that you have to adjust the KBD Track control panel knob so that you read 1.8V at the connector and then make any trimpot adjustments with this...
Thanks for the quick reply. Ok, so I adjust the KBD Track control panel knob so that I get +1.8V on CN05-06 and then adjust the KBD Track trimpot to get as...
You mean VR 10 instead of 12, right? It's like I don't have enough throw in the pots. The most logical approach I see is that I would center all VRs 1, 3, 10,...
I tried to contact crow a few times as for buyin a naked KLM-367A board but got no answer.... is he still making those ? ... and a ... I ... KBD ... from ... ...
I use an anti glare window cleaning solution that is like white foam. Nice finished and non-toxic .. I can't remember the name.. email me if you are intrested...
Whell I have my fully working P6 ... and Im very happy with it!!!! also I have few more.... in next few days I will try to make another one work....That wont...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
