Thanks, I found the one on oldcrows, but wanted the complete manual in PDF if possible. Also anyone knoe a good source for Tektronix manuals especially for the...
Ok, I'll confess... I am trying to nail the synth part to Steve Winwood's 'Valerie" and would like to see how it sounds on the Polysix. I'm currently playing ...
There are two easy ways... One, put it in UNISON mode. This will play all 6 voices at once, each slightly detuned. This effectively makes it a 6-oscilator...
just wanted to say, i put my polysix through a boss stereo reverb delay pedal tonight and it's wonderful! just a touch of each coupled with the stereo effect...
... You can make a convincing "Jump" brass on the PolySix. There are many Prophet- 5 sounds that can be recreated on the PolySix. The PolySix has filters that ...
... Fat PWM is the key: Fairly fast LFO applied halfway up onto PWM and just slightly onto pitch. Beef that up with a sub osc at 1 octave down and Chorus or...
Kristofer Ulfves
amber@...
May 3, 2005 9:32 am
967
Current situation - Trident powers up correctly, String section works OK except for unable to click the 16' and 8' on/off. Besides all section works. Brass...
... Probably the PW control is at maximum. I only have the schematics of Trident MK I (you can find it at "old Crow's"). It is very similar to MK II except for...
ok, totally confused I don't know what to do - hopefully someone will clear some things up for me because in four hours i'll have to be on stage with this...
OK - The moral of this story is, keep trying and you're bound to succeed. Sorry I freaked out there a half hour ago, but I have it totally in tune now. Now I...
This looks very useful, as I can create filter swells with the cutoff freq. But how do I use it? I can't use an ordinary sustain pedal (I've tried)... in the...
It needs to sweep between -5 volts and +5 volts. I'm not aware of anything currently commercially available that would do it. About 10 years ago, I did get a...
I have problem with my korg polsix- the battery problem. I have tried to clean the klm367 board and replaced the ic30 and ic31 and also changed the battery/...
I opened up and tuned my polysix yesterday, it took me some time but I got it rock solid. I think this is where I went wrong, not sure - I had it plugged in...
FIXED !! I found that the "technician" who tried to fix it before, put one 4011 in the wrong direction on the Synth control panel... fixing that caused the...
On Sun, 08 May 2005 00:14:43 -0000, Mike wrote ... You'll need something that will provide a control voltage. A swell pedal must have a battery to provide...
I had posted before if any one had used the trigger out on the DDD-1 to trigger the P6's arp. Well my ebay purchase showed up yesterday & I can let all of you...
What are the sympthoms ? generally it is needed to retace the corroded traces and replace parts that are places over or near them. See the procedure...
After replacing the NiCD battery with a Lithium in my Polysix, I'd like to do the same with my Korg Trident MKII and Kawai SX-210. On the Trident schematics,...
Is it normal for Trident and P6 to be noisy ?? Both of mine are very noisy, particullay the synth section on the Trident, and the P6 synth. Sounds like bad...
The sympthoms - the synth sound strange and I can't Switch the bank led's correctly. When I switch the synth on bank 1,2,4,7 are on. + to tape, from tape and...
Start be replacing the part that phisically seems as they were affected by the corrosion and retrace all bad (black) traces... does sound like a programmer...
Thanks, how about the SX210 ? should I replace the 1.5K resistor with a diode (the same way - a 1N4148 with the positive side of the diode facing the positive...
How to retrace? Can someone who not have done this before do it? What do you mean programmer problem? I have already replaced the ic30 and ic31. / tommy gil_we...
Send it to recovery. ... What do you mean programmer problem? I have already replaced the ic30 and ic31. / tommy ... phisically seems as they were ... does ......
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
