I tried to send this message: $rev. tx $F0 $00 $20 $32 $7F $7F $22 $02 $F7 $end To pass on the preset 2 but that did not work. I hears a signal in the BCF but...
Hi The bare minimum for what I think you are trying to do on a BCR2000 $rev R1 $recall 12 $end F0 00 20 32 7F 7F 20 00 00 24 72 65 76 20 52 31 F7 F0 00 20 32...
... The Behringer SysEx "Select Preset" command $22 should NOT be embedded in a BCL chain (between $rev and $end). It should be sent directly as a MIDI SysEx...
Thanks very much for your update. I don't have access to the LS9 at the moment but will try again in a week or so. ... I think I did try once using the thru...
Just for information, if anyone is interested, I failed to program BCR to control OASYS PCI with sysex. I used MIDIOX to observe what messages OASYS is sending...
Hi, I'm new to this group, a user from the kawai k3 group forwarded this group to me because I asked if it was possible to use a bcn44 with a kawai k3 (which...
... Sorry about there being no manual, but writing a good manual is always a lot of work. Since Behringer states that the BCN44 is "Discontinued" on their web...
Hi , I have just been writing a BCR2000 preset for the K3 so when it is completely working I'll put it in the files section and it might be a good start for...
From the Mountain Utilities website at http://home.kpn.nl/~f2hmjvandenberg281/ you can now download BCN44 Manager version 1.1.3. This version corrects the...
Thank you very much Mark! Cheers! Alex From the Mountain Utilities website at http://home.kpn.nl/~f2hmjvandenberg281/ you can now download BCN44 Manager...
Hi, iīve read here alot about custom settings via sysex files. So the basics are clear but how can i achieve Auto Sysex dump to Computer on Device startup or...
... If I understand your intention correctly, you can do this by using the BCF/BCR's "Request" and "LEARN output" features. See: "BC MIDI Implementation.pdf":...
Hi Mark, thanks so much for your impressive documentations& help here. Your comments teach me in the rigth direction, but theres something fundemantal wrong in...
Hi Mark, thanks so much for your impressive documentations& help here. Your comments teach me in the rigth direction, but theres something fundemantal wrong in...
... In any case the above BCL script is totally correct syntactically. I loaded it in BC Manager and uploaded it to my BCR without any problems. And what it...
... To my knowledge, you can't achieve this directly within the BCR itself. So the only solution would be to make the BCF/BCR receive a Request Data message...
I've been using the new Behringer Windows 7 x64 drivers on my system and I've notice that sometimes the names of my ports change if I have both my BCR and BCF...
Hi again... I wan to set up a Button to control besides it normal On/Off & Midi Functions the easypar & mode functions from a Encoder. So if i switch the...
Hi again... I wan to set up a Button to control besides it normal On/Off & Midi Functions the easypar & mode functions from a Encoder. So if i switch the...
... This is again something I think you can't do within the BCR itself; so you would have to loop the BCL statements back to the BCR (either directly or via...
Thanks Mark, especally youre comments helped a lot. I didnīt see at first Err14 message which wrong ".easypar off" message produces in my example. Iīve read...
Thanks Mark, especally youre comments helped a lot. I didnīt see at first Err14 message which wrong ".easypar off" message produces in my example. Iīve read...
2773
bc2000@yahoogroups.com
Mar 8, 2010 12:16 pm
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the bc2000 group. File : /Sysex Data/K4...
2774
bc2000@yahoogroups.com
Mar 8, 2010 12:26 pm
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the bc2000 group. File : /Sysex...
