Hi, I'm a new member as of a few minutes ago! I hope you all don't mind, but I made a new photo album called "mods" for people to share their Mono/Poly mods,...
Hi Casey ... The picture doesn't say too much. It would be more helpful to open the MonoPoly and take a shot from the inside to show where the cables go to. ...
Oops! Opened it up, and it doesn't go anywhere! All the wires are snipped! Guess it was an idea gone sour. I would still like to know what kind of cable I...
Hi Vince ... Originally the arpeggiator clock in is a switched trigger input (means: shorten tip to ground advances the arpeggio one step). To use it with a...
Hi Vince ... as you can read in the text, doepfer does: "...We offer such a special cable at a price of about Euro 20.00 - 25.00 (depends upon cable length and...
If you using a computer to sequencer and you want to sync the monopoly arp up to it then there is a simple way that I found to work with any synth with an arp...
Please help my VCO3 is way outta tune it is very high pitched and sounds real bad. I found the service manual online but I don't really know where to take it...
Hi Andy ... Hmm, where in the world are you located? I am in Munich germany and might be able to repair it... ... http://www.senso.dds.nl/ Senso is a very nice...
Florian, Thank you for the link. I'm in Michigan. prob a little too far to ship the keyboard for repairs. I will look through the vintage planet. Thanks again,...
Hej everyone! This is my first post and it's no funni at all. I was to tune my 3rd osc when a PCB that was hanging loose came in contact with the PSU-unit. Do...
Hi alexander ... Yes there is rescue, but this is now a job which should definitely NOT be done by yourself (letting this pcb hang free around proved, that you...
Thanks! Yes, you're right. Never again that I touch the insides of a synthesizer.. :) Is there a clue to what has happened? Maybe I have to buy a new PSU-unit ...
Hello Alexander ... One cannot tell, what really happened. The synth has to be demounted completely and one has to test and reconnected every module ...
Hello everyone I'm looking for help on mounting the Mungo midi kit on my Monopoly and Sh 101. If there is someone who have installed these kits please write me...
I have a Korg Mono/Poly MP-4. I was able to tune each Osc on Circuit board KLM-398. However, as you ascend the keyboard up from the lowest note to highest...
Hello. I am new to the group and a new proud owner of a Mono/Poly. I see there hasn't been any activity in the "patches" section for a few years. Does...
Hi ... Check the CV at the CV-Out; if this does not read V/Octave, then adjust VR2 on the processor board (KLM-356). If this reads correct V/Oct it would...
yeah seems you are right. i posted some of my own a few years back but it seems no amount of encouragment could get others to do the same. :( ... I see there...
well once again to do so please download the patch sheet from the files section. fill it out then scan it back into your computer. please upload it to the...
Hi, My name is Nick, from Australia and I have owned a Mono/Poly for about one week! Up until yesterday, it worked 100% but I fear it's dying now... Triangles...
Hi The higher the Resonance the lower the level of the signal. This explains why the distortion is gone. May be you simply switched the output level to "high"...
Hi Florian, Thanks for the reply! I don't think that's it, as there is no change in this even with headphones directly plugged into the Korg. I have also...
Have you checked that the Arppeggiator isn't set to latch. with MG2 at a high speed this can make thigs sound like you discribed. I often have moments when its...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
