What you have read seems to be at least 10 years out of date. Check out Roland GI-20, GR33 or used GR30, Axon Ax100 or Yamaha G50. These are the best...
13772
Nik
fasciola2000
Nov 1, 2003 8:52 pm
Opposite to my experience. The AX100 can cope with 16th notes so long as you are careful about your damping. Too much right hand damping and it either produces...
13773
Nik
fasciola2000
Nov 1, 2003 8:52 pm
...And my Axon triggers just as well on low strings as high strings.....unless you have Fingerpick switched on ....which I don't.....even when I am...
13774
Nik
fasciola2000
Nov 1, 2003 8:52 pm
I did, but no longer have the G50. With a magnetic pickup (Yamaha G1d) the G50 was a little more inclined to glitch or miss notes. No noticeable difference in...
13775
nalaregeork
Nov 1, 2003 10:42 pm
Thanks the piezo bridge is already on my list of tracking improvement features to have (eventually) I wouldn't mind the occasionaly missed note but the wrong...
13776
Jesse Brown
jbetherea
Nov 2, 2003 3:17 am
There are several MIDI footboards with assignable CC pedal inputs.. you could easily configure it to send pitch bend data, and set the bend range on your synth...
13777
bleuteuth
Nov 2, 2003 4:55 pm
I just got a GK-1 with no instructions. Do any of you know of some online instructions for how to physically set it up with a gutar, and what the procedures...
13778
Matt Picone
matman67b
Nov 2, 2003 5:04 pm
When I use my midi guitar, I'm getting a bad ground loop. Here's my setup: http://www.mysticworks.com/images/midiguitarsetup.gif Is there any way to solve...
13779
Philip
pgruchet
Nov 2, 2003 6:30 pm
You'll find a useful PDF about the Yamaha G1D pickup from: <http://www2.yamaha.co.jp/manual/english/> ... Bye, P...
13780
Jürgen Busch
juergenbusch...
Nov 2, 2003 6:37 pm
Hi, The GK-1 from ROLAND normally has his position staright in line between bottom of guitar and the bridge. There are two ways (holder units) to fix the Gk-1...
13781
Graeme Jaye
spaincd
Nov 2, 2003 6:40 pm
Hi Matt On 02/11/03 you wrote; MP> When I use my midi guitar, I'm getting a bad ground loop. Here's my MP> setup: First of all, what have you done to date to...
13782
Steve Coates
snipedoguk
Nov 2, 2003 6:58 pm
Hi Matt, Whilst endorsing all of the below, please don't forget that the units may well also be earthed through any rack you have installed them in. If the...
13783
diversified.electroni...
diversifiede...
Nov 2, 2003 7:05 pm
Hi Matt, you are doing the first thing right in terms of having everything plugged into a single power source. In addition to the other suggestions... Do you...
13784
Matt Picone
matman67b
Nov 2, 2003 9:35 pm
... Hi Graeme, Steve, and "diversified". Thanks! The loop only happens when I connect cables to the guitar. If I remove either the 13 pin or the 1/4", it goes...
Hello - I like pedals for pitch bend because I love the old wammy, and accompanying technique. But for onboard CC stuff, one of the coolest things I've been...
13787
Robert Edgar
lull@...
Nov 2, 2003 10:41 pm
... I have a GR-33 I play with my Strat, and using my whammy bar gives pitch bend information that controls the selected MIDI sound. Unless I'm missing ...
13788
Steve Coates
snipedoguk
Nov 2, 2003 10:53 pm
... Hi Matt, Just to clarify, if you connect BOTH 1/4" AND 13 pin you have a hum problem, and if you disconnect EITHER of these it goes away? Are you running a...
13789
diversified.electroni...
diversifiede...
Nov 2, 2003 10:57 pm
Hmmm, almost sounds like the guitar has a ground issue/loop? If you touch ground while everything is plugged in, does the buzz go away? ... From: Matt Picone...
13790
Tim Burke
frankenstrat11
Nov 2, 2003 11:38 pm
Hi I too am fighting the ground hum problem with a similar set up (though not exact) to Matt's. My question: I have two different racks -- one for guitar gear,...
13791
diversified.electroni...
diversifiede...
Nov 3, 2003 12:59 am
I kinda came at it from the angle of a band setting up the PA. I learned early on when I ran sound not to plug in the mains and the mixer+EQ+Effects etc. into...
13792
djn125
Nov 3, 2003 1:01 am
I just got a casio dg-20 but something is rattling around in the neck (something heavy). Does this thing have a truss rod? I poked around and didn't find an...
13793
Dave Zobel
dzobels
Nov 3, 2003 1:10 am
Hi, folks. In my opinion, only Nik is coming close to speaking clearly on this thread. The original post mentions "16th note chunka chunka" I've found that...
13794
bleuteuth
Nov 3, 2003 1:26 am
Does Yamaha now have Roland product support documentation? Sorry if I wasn't clear. I am looking for assistance with a Roland product. The product is a Roland...
13795
al@...
Nov 3, 2003 4:32 am
Hey, I got rid of the hum.! Hum Eliminator - about 60$ at Guitar Center.com It works by using a transformer to make no contact connection. Also allows you...
13796
JAMES FOWLER, III
jamesrobertf...
Nov 3, 2003 5:19 am
finding a pickup is gonna be a bitch. -jim tgalf <tgalf@...> wrote: Interesting. I have 2 8-string necks for building a doubleneck electric but I have...
13797
Jürgen Busch
juergenbusch...
Nov 3, 2003 5:34 am
Hi, yes ROLAND worldwide still have service documentation for the gk-1 pickup!(includes circuit diagram and mounting /adjustment instruction). the hex-midi...
13798
Nik
fasciola2000
Nov 3, 2003 7:30 am
Yup. Heavy right hand damping screws up MIDI guitar. Heavy RAH damping gives you a noise laden CHUNK sound instead of a clear note. That's the whole point....
13799
guitarpugs@...
vaithal5150
Nov 3, 2003 10:55 am
Hi there, The DG-20 has a flat bar in the neck, not a truss rod more likely for balance. It's usually held in place with some silicon. [Non-text portions of...
13800
cwmurray3255
Nov 3, 2003 2:39 pm
Hello All, I would love to get an acoustic sound out of my roland ready strat, like my Godin LGX-SA. RMC and Fishman have the powerbridge type setup, but is...
