As amazing as it may sound many people do not realize how easy it is to LEGALLY stop paying for their groceries! This is how the one hour television show began...
I simply can't believe how main stream this program at http://www.wrldofproducts.com has become. Between tv shows, radio programs, people talikng about it and...
Some of you asked for proof of my savings from the program I used at http://www.wrldofproducts.com Well here it is go to http://receipts.tripod.com to see some...
Quick and hopefully simple question, If I want to wire up two CV outputs per bank, like Gary Chang's Milton, do I need to do anything special? I was thinking...
chang's version has a four channel voltage adder. I've made a few more like this since. Each attenuator is bi-directional (also inverts the input) and it...
Hello all - Introduction - I've been slowly building a modular synth. It's been about 2 years now, and I've been mostly building motm kits, with some blacet...
Steve There are a couple of 1/4" jack based versions in the photos section. I suggest that you 'beware' about MOTM format. Depending on what you mean it ...
Thanks for the info. No, what I mean by motm format in this case is just the overall size of the thing - probably along the lines of what you're getting. I'm...
Two for now. I'm doing tiny bits of this project at a time for now. My engine board says REV 1.4 1. There are two unmarked diodes to the right of the "to jm3"...
HI. The .01's are just bypass caps. they can be .001's, even .1 in some instances. In short - buy either the .001s or .01s. Which ever you need. Mouser has...
Just a quick question about capacitor values. Is c1 .022mf as indicated on the BOM? The board, and the schematic just say .022, only the BOM says mf. My...
Sorry for the confusion. Fu and mf are the same thing. Very common nomenclature substitutions. . Using a 'u' is a lazy man's way of doing the greek micro...
Damn I am excited about the new rate I am on. When I signed on for my first house 15 years ago the rates were nothing like they are now, and after a bit of...
thomasina.kirby3651@...
Dec 4, 2005 11:17 am
212
I dont see the ACB boards listed at BCM. Are they still available from Peter directly? I've finally dug out my Milton board set which has been carefully ...
Work continues here on milton, start and stop a lot because of the season. 2 nagging questions are pestering me, for Peter or anyone else with ideas. 1. I...
I bought the one specified in the parts list from digikey, not mouser. i would have had to buy 15000 of em from mouser so i got ten from digikey instead....
dont worry to muuch about the voltage rating, so long as it is higher than the voltages in the circuit you are ok. it sounds like you got surface mount caps?...
Try part no. 399-1918-ND from digikey. It's 100v but it'll probably work. I haven't fired mine up yet so I'm not sure if it works yet, but I asked a similar...
Damn, it has sure been a while... I just realized today that it's been 18 months since I went out with a special lady last, but I'm pretty happy to be...
thomasina.kirby3651@...
Jan 10, 2006 3:26 pm
218
I am new to this stuff so forgive me if this is a dumb question. All my jacks have three contacts. One tip, one sleeve, and a third that connects to the tip...
Yeah I know, I never really thought this stuff would work either, but honestly I stand totally corrected. This place http://www.luvvisherenow.info/ezzx is...
thomasina.kirby3651@...
Jan 12, 2006 2:44 pm
220
I wonder if the jacks are 3.5mm, 1/4", or banana? ... -- *David Bartz* Extremist, Anarchist, Evildoer, Exegete, Director of Propaganda: Bill O'Reilly Institute...
Hope he's enjoying a good vacation! Anyway, I'm still looking for an answer to my question about resistors some 6 messages back - can anyone reading this help...
R2 is 1k. R1 - 330 ohm is fine. the output is more governed by the value of the 430K in the feedback. You may need to play around with this. 470K to 510K ...
I am not sure how to hook up the two DPST switches for voltage control and async. i think mine are DPST (on off). they have a total of four contacts on each,...
Hi On the demo on buzzclick (http://www.buzzclick-music.com/miltsamp.html) it is playing one part at full speed, and another at 1/2 the speed. "This...
When I order my PCB's is is possible to get 3 bank boards w/ the programmable pulse banks, and one w/ the gates and led's, and not get the 2 standard bank...
