Just a quick question about capacitor values. Is c1 .022mf as indicated on the BOM? The board, and the schematic just say .022, only the BOM says mf. My...
Sorry for the confusion. Fu and mf are the same thing. Very common nomenclature substitutions. . Using a 'u' is a lazy man's way of doing the greek micro...
Damn I am excited about the new rate I am on. When I signed on for my first house 15 years ago the rates were nothing like they are now, and after a bit of...
thomasina.kirby3651@...
Dec 4, 2005 11:17 am
212
I dont see the ACB boards listed at BCM. Are they still available from Peter directly? I've finally dug out my Milton board set which has been carefully ...
Work continues here on milton, start and stop a lot because of the season. 2 nagging questions are pestering me, for Peter or anyone else with ideas. 1. I...
I bought the one specified in the parts list from digikey, not mouser. i would have had to buy 15000 of em from mouser so i got ten from digikey instead....
dont worry to muuch about the voltage rating, so long as it is higher than the voltages in the circuit you are ok. it sounds like you got surface mount caps?...
Try part no. 399-1918-ND from digikey. It's 100v but it'll probably work. I haven't fired mine up yet so I'm not sure if it works yet, but I asked a similar...
Damn, it has sure been a while... I just realized today that it's been 18 months since I went out with a special lady last, but I'm pretty happy to be...
thomasina.kirby3651@...
Jan 10, 2006 3:26 pm
218
I am new to this stuff so forgive me if this is a dumb question. All my jacks have three contacts. One tip, one sleeve, and a third that connects to the tip...
Yeah I know, I never really thought this stuff would work either, but honestly I stand totally corrected. This place http://www.luvvisherenow.info/ezzx is...
thomasina.kirby3651@...
Jan 12, 2006 2:44 pm
220
I wonder if the jacks are 3.5mm, 1/4", or banana? ... -- *David Bartz* Extremist, Anarchist, Evildoer, Exegete, Director of Propaganda: Bill O'Reilly Institute...
Hope he's enjoying a good vacation! Anyway, I'm still looking for an answer to my question about resistors some 6 messages back - can anyone reading this help...
R2 is 1k. R1 - 330 ohm is fine. the output is more governed by the value of the 430K in the feedback. You may need to play around with this. 470K to 510K ...
I am not sure how to hook up the two DPST switches for voltage control and async. i think mine are DPST (on off). they have a total of four contacts on each,...
Hi On the demo on buzzclick (http://www.buzzclick-music.com/miltsamp.html) it is playing one part at full speed, and another at 1/2 the speed. "This...
When I order my PCB's is is possible to get 3 bank boards w/ the programmable pulse banks, and one w/ the gates and led's, and not get the 2 standard bank...
Hi, you can only order the Milton as a complete kit at bigcitymusic.com: http://www.bigcitymusic.com/product.asp?cat=New&pid=1000464 AFAIR there is only one...
So, Any ideas on how they make one part of milton play at full tempo, and another section play at 1/2 the speed? Is that a function of this sequencer, or...
Mouser doesn't carry a 4516 any more? I found Newark P# 70C8677 but perhaps someone can give me a suggestion from the Mouser Catalog? The only reason I ask is...
I emailed him with some troubleshooting problems like a month ago and he got back to me right away with some things to test. I sent him the results as he...
Hi no doubt Peter will be along sooner or later... in the meantime, are the 074s on your Cv boards getting power? i remember 2 slightly obscure jumpers that...
Hey. On the CV boards do I need to install 10uf electros too? because I didnt do that and no I didnt install a jumper over there that might be it . Thanks...
Hello! I have a brand spanking new Milton Sequencer in the Modcan format that I just received from Cynthia. I don't have a modular any more so will offer it...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
