To any of you that have been wiating (patiently) for ordered materials - it's all shipping tomorrow. I must apologize for the delay. My mother has been taken ...
I haven't seen a clear answer for this as yet. Once and for all, what value bypass caps do I use in: a) Engine Board PCB indicates 2 x 0.01uF and 16 0.1uf BOM...
... The definitive answer - it doesn't make a difference! It you need one though, then go with .01 The pots you seek, as indicated on the on-line BOM, are...
If any of you are buildng bank boards using the Panasonic pots speced on the on-line BOM, the following link is the source for the type of knobs you'll need: ...
I have uploaded a picture in the photo section of a custom Milton recently completed for a customer to fit in seamlessly with the decor of massive Buchla 200. ...
Just starting on building Milton (finally). A few things that I am confused about (probably not the last ones either): (1) I'm assuming that the 10uF...
Jeff First off, thanks for writing 1) I would stuff all the 10uf's - As they are filter caps, they can't hurt. 2) The SWR pads are for the return of the...
After *many* weeks of working on Milton, I tried it out today. Most of Milton appears to work. However, I have 2 problems (2 that I am aware of) that I am...
... Have you checked the supply voltage? What voltages are you running the sequencer from (12 or 15)? I am not sure what you mean by pre-triggers - please...
Peter, Thanks for your suggestions. I'll try to clarify (1), and I'll review your suggestions for (2) {pulse bank switches} later. ... Supply voltages of...
... looking at the above, it would appear to me that the problem is specifically to do with the second lowest bit of the counter - something appears to be ...
... I'm not sure exactly where to "hang" the .01uF caps, so I connected one to step 13 and one to step 15, with one side of the cap connected to the socket's...
First, I'm really glad this dialog is happening here on this list as it will serve as a troubleshooting guide for other kit builders in the future. That ...
... Sounds good. My intention was "The more eyes, the higher the probability of finding a solution." Thanks for the detailed troubleshooting instructions....
... pin cables from bank board to bank board are less than 6 inches long. OK, this ain't the problem, continue... ... ...how are the grounds of these two...
... The supplies are independent - they are not physically connected from supply to supply. The only possible connections between the supplies are through...
Enter your vote today! A new poll has been created for the milton-sequencer group: Would you be interested in an ASYNC Pulse Generator assembly for your...
milton-sequencer@yaho...
Feb 19, 2004 5:11 pm
67
Miltonheads, I am in discussion with someone to create a PIC which would generate a pulse out whenever a state change occured in a four bit binary word. The...
Not a problem... K... synchronous VC mode has it's benefits for sure. But it behaves like a sample and hold - .one can get it set up 'just so' (meaning...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the milton-sequencer group. File :...
milton-sequencer@yaho...
Feb 21, 2004 5:56 pm
71
Thanks for the elaboration. Now it makes sense to me. Count me in! Romeo ... behaves like a ... perfectly) at a ... clock speed ... going to be ... that...
OK, with 13 interested parties (five more I know will want it that haven't responded) and one (Cynthia) who will be wanting multiples of this, it seems...
The prototypes of the PIC for the Async Clock Board (heretoafter known as the ACB board) are on their way to me. It should take but a hald week to finalize...
Miltonites, I have received the prototype PICs and have as well installed its prototype driver boardlette into a unit here and outside of one small issue which...
The initial Asynchronous Clock Board (ACB) order is now being placed. Cost $22 - which includes 1 PIC, 1 ACB boardlette, instructions and shipping. the ACB...
