You did not specify what your tech replaced. http://www.kleonard.com/gear/mg1.htm Read my story, especially the part about the MM5823 chips. It is possible...
I'm guessing that you tried to replace U3. If you used a socket, pull the chip out and check for signal on pins 13 and 14 of U2. If U2 is not putting out...
Hi I am new to this group. I recently acquired a fairly cherry MG1 off of Ebay. This is the end of a decades long quest to get one of these beasts. I was about...
Hello and welcome to the group! As far as the keys being kind of off... If you have only the organ slider up in the mixer, does each note play correctly? Do...
hi, my name is omar do you know where i can find a replacment pot for the tone tune??? To: moogmg1@yahoogroups.com From: babysealclub@... Date: Fri, 1...
Todd, Yes the 10k pot is what i am after. Is it a pc mount like the origional? If so can i purchase two??? cheers omar To: moogmg1@yahoogroups.com From:...
Just wondering if it's possible to use a regular 'expression pedal' (like the Moog EP-2) with the MG1. If I understand correctly, such pedals take a voltage...
the ep 2/ ep1 / and mp201 are all CV Expression pedals.. so yes, it will work fine.. I have the mg1 and the mp201 pedal.. works seamlessly ... From:...
Okay. Thanks for the advice - I did pick up a Moog EP-2 in 'as new' condition. It's a great expression pedal. Let me see if I understand correctly. There are...
I've been missing a G# off my MG-1 since I got it 5 years ago. Anyone have an extra black key they could sell? Up to $25, can Paypal (or whatever method)...
Try synthparts dot com. Â -TF ... From: Wayne Griffin <ingsoc_1979@...> Subject: [moogmg1] Black Keys To: moogmg1@yahoogroups.com Date: Sunday, July 26,...
Well I did the output Mod on mine. It sounds a lot better with those old resistors out of the way! And the 1/4" jack popped right in place. Though it was a...
I modded my MG for CV control of cutoff, and of Detune. Haven't done PWM yet but its on the list when I get back into modding mode. You can get CV control of...
Thanks for the info, and the link! I have done some googling. I didn't get vary much info. Kind of the typical google white noise. (who knew there were moog...
Hey, so I just bought a mg-1 a few weeks ago and tone source 1 has started going out of tune after the synth has been on for about 5 minutes. Â Tone source 2...
joined just to tell you all about a free VST that mostly models our beloved old synth!! http://sarvst.110mb.com/SAR%20VSTs/Page2.html scroll down to REALITY...
233
moogmg1@yahoogroups.com
May 10, 2010 11:03 pm
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the moogmg1 group. File : /Reality.zip ...
I was browsing around on the youtube and came across a mod that I really want to perform. It involvs adding a switch that modulates oscillator 2's pitch with...
Hi I found your thread concerning the scale and the MG-1 on the Yahoo Moog MG-1 Group. I know it's been almost 3 years ago you had the scale problem with the...
Scaling a VCO can be frustrating and confusing - mostly due to poorly written and convoluted calibration procedures. Inconsistency in circuit design and...
Good afternoon, My name is omar. My question is has any one done the ext audio in mod?? \ Cheers, Omar To: moogmg1@yahoogroups.com From: KLBR@... Date:...
