Hi there. All I need to make my sh101 complete is a green slider pot. Does anyone know where I might find one? I've checked Ebay regularly and done numerous...
Hello, Vintage Planet seems to be out of the mech parts. The Ebay seller technologytransplant sometimes sells these combined with other spares, sometimes in a...
Hi there, I'm new to the group and I have recently purchased a SH-101 in extremely good condition however it seems that the VCF Modulation slider does not seem...
... Hi Phil, At what value is the envelope amount in the filter section? as if this is set to a high value it will also lesson the effect of the mod amount. ...
... Hi Paul, I would say the envelope amount is about 50%. Having said that I'm pretty sure that I tried almost all permutations and one would have been to set...
... Hi Again, Tried setting the envelope amount on the VCF to being very low. Still having no effect on the VCF modulation whatever I do. Definitely not...
Sounds like the slider is kaput. If you are handy with a soldering Iron it's an easy swap out. The sliders are easy to get online. You will need the schematic...
Hi Hugh, Sounds like a relatively simply job, could you direct to where I can get the schematic and where to get the sliders from? This would be a great help. ...
Ebay seller technoloytransplant got the parts you need. Just mail him. ...
Christian T
cybercardinal@...
Jun 15, 2009 7:44 pm
1912
That's the guy I bought them from. The schematic is available from this user group. Click on the files section on the left hand size Remember an SH-101 is not...
The PWM slider probably was fine and the problem is the calibration of your synth. You need to adjust the Pulse Width with the oscilloscope until you get a 1:1...
Hi, Thanks for the update everyone. It looks like it may well be a calibration issue then. This rings true because I was just playing along with my other...
I have read various postings on the net that it's possible to sync the 101's arp and/or sequencer via a trigger pulse from either a sample or drum machine. I...
How does the 606 rimshot sound like? Mine doesn't even have a rimshot ;) Whenever I need an audio out to feed analog trigger ins (usually using an MPC but any...
... Err... good point! Sorry, I meant the 909 rim shot of course! ... Yeah, I guess this is pretty much the pulse waveform sample I already have. I might give...
Your 909 rimshot sample is, like any audio signal, AC but the pulse I mentioned is supposed to be DC-like (if you just draw in the positive area). Also check...
Howdy, If you know someone with a TR-909, use the trigger out that is programmed with the wood block sound. Note the wood block out will NOT trigger the 101...
Hi, here's an update to my problem. Last night I went through the process of calibrating my SH-101 (it was a tedious process). It's now in tune (close enough...
I've got a 606 and it as has been mentioned it has two trigger outs (controlled by the high and low toms). These can be used to trigger the SH101 either by...
Hi again, What you can do it's to check if the slider is good, you have two options. 1.- Check with the multimeter (ohms) from the pin 1 and pin 3 and it shol...
I just have a couple of quick thoughts: 1. has the 101 been modified at all (sorry you may have mentioned in a previous post, but I'm not trawling through all...
Hi, more updates, I tested the resistance of the VCF mod slider as suggested and it is almost certainly broken as I get the 100Kohms resistance between pin1...
Hi oxygeno1313, I swapped the sliders like you suggested and the VCF modulatino now works perfectly! :-) I'm waiting for the new slider and will replace both...
Get a de-soldering pump, about 2 quid on e-bay ________________________________ From: sh-101@yahoogroups.com [mailto:sh-101@yahoogroups.com] On Behalf Of...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
