Hi everyone, I'm a new (Second time owner) of TubeFex, as I'm lucky enough to find a mint TubeFex from my local store for just 100, hehe Here is a pic of my...
Please unsubscribe me from the mailing list. Thanks ... From: donghua1217 To: tubefex@yahoogroups.com Sent: Monday, December 05, 2005 5:06 AM Subject:...
Hi John, Just wanted to let you know I have done over 250 of the batteryless memory mods to Session 2000, Transtubefex, Tubefex Bassfex and Profex 2 since...
Cool! The more NiCd batteries we can get out of those units, the better! I should make those changes. It also works in the PC1600 MIDI fader box. Look for it...
Good news on the PC1600. Also curious about other older effects units and even the Autographs. I know you are a busy gut, but could you help me out! I use a...
Hey Ken, You can add RAM chips and up the memory to either 128k or 256k. Don't use ZMD parts, because nothing non-volatile would be stored there (if memory...
Yes, it is a Peavey Midi-Streamer. I have tons of the correct chips ( from replacing the Profex 2 chips) so I will give it a shot. Thanks, John Ken Fox 814...
Well even if you're not looking for love, and just a bit of fun thought I'd give you all a tip. So you can stay away from all the bullcrap fake profiles places...
suzan.johnston9422@...
Dec 9, 2005 9:17 am
8786
Hi all I've got a TranstubeFEX rack with all firmware and batteryless upgrade and a Voice Crystel 256K RAM card, and a PFC-10 with cable for sale. What's the...
I am looking for a cc pedal for my transfex 212s with midi pedal board. Or what other kind of pedal can be used as the CC-pedal or expression pedal. Thanks...
That will work. Also, ANY standard volume pedal will work with a "stereo to mono" Y cable. Plug the stereo end (Tip, Ring, Sleeve) into the midi controller...
... \i went and bought the y cable. but now i get a very bad buzzing sound. I am using a morley pro volume pedal with the power supply comming from my skb...
Are you using this with a PFC-10? It shouldn't be adding any buzz. I'm using two standard volume pedals with Y cables for my CC pedals. If you're using the...
I am using a peavy transfex pro 212s version 1.5 with a pfc 10 midi foot controller connected via a 8 pin midi cable. The volume pedal is a morley pro series...
... Hoi, lauren, I used my TTF stuff as my primary bass preamp and effects for several years, then a couple years ago I got a Roland V-Bass. The TTF then ...
Hello All. I recently downloaded Fexmanager v1.15, I installed it and setup my midi ports and the program worked fine. Today I tried to start the program and...
FYIW, I'm using Windows XP Pro on a AMD XP system, and I have a Emagic AMT8 8x8 usb midi hub. It's funny because the program worked fine after I first...
Hi guys, I'm new to the group but not to effects and electronics. I've got a question or 2 about the units. First off let me tell you I have had a Peavey...
Bummer... But what a cnace for some lucky soul to score on some great gear! Hey Greenboy, are you interested in selling just the memory card? I already have...
Hello All. I've recently acquired a Peavey Tube Fex, and while changing out the tubes, I noticed that the label on the center eprom is labeled v1.0. I've...
You will also need to do a resistor change (actually parallel one around another) and add a motor pot ground strap for the later versions. Check this site for...
Hey everyone :) ok I have run into another problem my second Tubefex has bit the dust :( ..Yes I know its death to your ears right.....Well I tried getting the...
Firstly I want to again thank Ken for the upgrade and walking me through it. Works like a charm. I also got the upgrade from peavey. Jimmy was very helpful and...
Check the pins for continuity with an ohm meter, I recently repaired an almost new cable, had a broken solder connection on one pin! Ken Fox 814 Wilburn St ...
My lcd screen in the tubefex has gone haywire missing characters etc I fixed it a couple of months ago but it is at it again, does any one know where I can get...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
